This industry-first and unique dual band Ka/Ku LNB is designed to receive Ku (10.7 to 12.75 GHz) and Ka (21.4 to 22.0 GHz) TV, radio and data channels with linear polarity (Horizontal/Vertical) from the same orbital position at 25.5° East. It can be used with standard offset dish antennas of 60 to 90cm diameter and F/D of 0.6.
 
The LNB has two ports – one supporting either Ku or Ka and the second port fixed to deliver Ka-only. The selection between Ku and Ka band is based Tone Burst or DiSEqC 1.0 commands. The product is supplied with a 40mm ring adapter to ensure compatibility with the majority of already installed legacy dish antennas.


Eutelsat 25.5E Ka/Ku coverage over the MENA region


Technical specifications
Input frequency range 21.4 GHz ~ 22.0 GHz (Ka band)
IF frequency range 950 MHz ~ 2150 MHz (Ka band)
Low band input frequency range 10.7 GHz ~ 11.7 GHz
Low band output frequency range 950 MHz ~ 1950 MHz
Low band LO frequency
9.75 GHz (Ku band)
High band input frequency range
11.7 GHz ~ 12.75 GHz
High band LO frequency
10.6 GHz (Ku band)
Noise figure
1.2 dB typ.
1.5 dB typ. (1.7 dB max.) (Ku band)
LO frequency
20.25 GHz (Ka band)
LO temperature drift ±3.0 MHz Max.
LO initial accuracy ±1.0 MHz Max.
LO phase noise @ 1 kHz -50 dBc / Hz max.
LO phase noise @ 10 kHz
-75 dBc / Hz max.
LO phase noise @ 100 kHz -95 dBc / Hz max.
LO phase noise @ 1 MHz -105 dBc / Hz max.
LO band selection None (fixed to 20.25 GHz) 
Conversion gain
50 dB ~ 60 dB min.
Gain ripple (over 26 MHz bandwidth) ±0.75 dB
Gain variation (over full band) ±5 dB max.
1 dB compression point (@ output) 0.0 dBm min.
Cross polarization isolation 18 dB min.
20 dB min. (Ka band)
Polarization selection - Vertical 13 V
Polarization selection - Horizontal 18 V
Control signal Cc (band switching)
0/22 kHz +/-4 kHz
Output VSWR
2.5 : 1 
In band spurious level -60 dBm max.
Current consumption
180 mA max. @ 11 V ~ 20 V
Operating temperature
-30 °C  ~  +60 °C
Output impedance
75 Ω
Output connector type
F-Type (female)
Recommended Dish Size 60 ~ 80 cm (F/D ~0.6)
Weight 540 g
Remraks 13/18V command is used to select between:
- Vertical and Horizontal polarization for Ku and Ka band
0/22KHz is used to select between:
- 10.7 to 11.7 GHz in Ku band (ie 9.75GHz LO)
– Low band- 11.7 to 12.75 GHz in Ku band (ie 10.6GHz LO)
– High band- In Ka band, the LO is fixed whatever is the 0/22 KHz signal (ie 20.25 GHz LO)
Logistical info
Packaging dimensions (W x D x H) 16,1 cm x 9,45 cm x 13,1 cm
Packaging weight 0,645 kg
Quantity per Carton 30 pcs
Carton dimensions (W x D x H) 82,5 cm x 30,3 cm x 28,2 cm
Carton weight 19,35 kg
Quantity per pallet 360 pcs


Images
Drawings
FAQ
Q: What is an LNB?
A:
An LNB - Low Noise Block (also called an LNC- Low Noise Converter), it is used for communications (broadcast) satellite reception. The LNB is usually affixed either in or on the satellite dish and its purpose is to collect and amplify the satellite signal received from the dish and then down convert the signal to lower more manageable IF frequency which can then be carried over standard coaxial cabling to the receiver.
Q: What is a feedhorn?
A:

The feedhorn is a part of the LNB and works like a directional horn. Its function is to capture the signals reflected from the dish and to shield the LNB from receiving extraneous radiation from other sources. These collected signals are then passed form the horn to the electronics within the LNB.

Q: What is the difference between a Quad and Quattro LNB?
A:
A quad or quad switch LNB is an LNB where the multi switch is integrated into the LNB and gives 4 independent output ports for the connection of 4 receivers. A Quattro LNB has 4 outputs and each of the output’s is set to one of the differing polarities, the 4 outputs are V/L, V/H, H/L & H/H. A Quattro LNB is normally used to feed a multiswitch which then allows the distribution of the signal to any number of satellite receivers. All four outputs of a Quattro LNB are marked accordingly with V/L, V/H, H/L & H/H to avoid confusion and malfunctions when connecting to the multiswitch.
Q: What is the HsQuare Technology?
A:

HsQuare is a unique waveguide technology which may be coupled with a slightly larger feed horn design to deliver better RF performances compared with common circular microwave waveguides.

Q: What is a monoblock LNB?
A:
This design consists of two independent LNBs in a single housing and allows a user the potential of receiving the signal from two different satellites which are at slightly different orbital opposition from a single dish installation. The switching between the satellitesis achieved via the use of DiSEqC signals or Toneburst (Mini DiSEqC). Monoblock LNB’s are available mostly for satellites with a fixed 4.3° or 6° spacing and the range covers Ku band monoblock switch single, twin and quad outputs.
 
Example where a 6° monoblock LNB could be used is for the reception of ASTRA 1 (19.2° East) and Hotbird (13° East) or with 4.3° distance for the reception of ASTRA 1 (19.2° East) and ASTRA 3 (23.5° East).
Q: Why can I receive only one satellite with my monoblock LNB?
A:
For dual satellite reception the dish is normally initially aligned to the weaker of the two satellites and then some slight adjustment can be made ensure the best possible reception from both the satellites. A monoblock installation will require a slightly larger dish size than if only one satellite location had been chosen. Monoblock LNBs are designed to work on a specific dish size and it’s important that the correct dish size is installed or both satellites signals may not be picked up at a sufficient level of strength to guarantee reliable reception.
Q: What is a wideband LNB?
A:
With a wideband LNB having only one local oscillator (e.g. 10.4GHz), and captures the full frequency spectrum of the satellite (300MHz to 2350MHz) which are delivered over two outputs from the LNB. One output carries all the vertically polarized signals whilst the second output carries all the horizontally polarized outputs. Whilst most of the current multiswitches on the market do not accept a wideband input the newer multiswitches such as newer Unicable switches are capable of accepting this as their input.
 
Caution: Wideband LNBs are not conventional twin LNBs. Wideband LNBs can be connected to a Unicable multiswitches that is designed for this purpose, or, if connected directly to a receiver, only with a suitable tuner.
Q: What does Unicable mean?
A:
Unicable is a new method for distributing satellite television. Several receivers (currently up to 32 in accordance with standard EN 50607) can be connected to only one single chain which is not possible with a conventional satellite distribution (star distribution in multi-switch mode). For more information about Unicable, see www.inverto.tv/what-is-unicable-2
© 2024 FTA Communication Technologies S.à r.l.   Legal terms of usePrivacy policy Site by Medya-T